Quick answer: Mil-spec fasteners are bolts, screws, nuts, pins, and rivets built to military or approved industry standards such as AN, MS, NAS, and NASM. The drawing, specification revision, material, finish, and contract clauses set the requirement. DLA’s QSLM lists qualified manufacturers and QSLD lists qualified distributors. DLA closed that program for threaded fasteners in February 2023. The Berry Amendment and DFARS 252.225-7009 specialty metals compliance set different restrictions.
A replacement bolt that fits the hole still fails procurement review when its material, finish, or records do not match the drawing. The damage shows up in three places: assembly kits pulled into quarantine, specialty metals compliance holds under DFARS 252.225-7009, and counterfeit hardware coming in through undocumented brokers.
The supply base has also shifted twice since 2021. When DLA stood down its Industrial Hardware supply chain in 2021, it split roughly 900,000 hardware items between DLA Aviation and DLA Land and Maritime. In February 2023, DLA ended its Qualified Supplier List program for threaded fasteners, quick release pins, and rivets. Your process has to tell look-alike hardware apart without losing the specification revision, manufacturer identity, or lot information.
How CSG Supplies This
Military and defense fastener support from Component Solutions Group (CSG) starts with your drawing, not a catalog. CSG is an engineered fasteners distributor and supply chain partner, and a Bufab company. We do not manufacture fasteners. We source, document, and deliver them.
Our capabilities include design-assist engineering, global sourcing, kitting, vendor-managed inventory (VMI), sort and containment, and light assembly. CSG is ISO 9001:2015 certified, AS9120 Rev B certified for aerospace distribution, ITAR registered, a DLA Qualified Supplier, and holds JCP Certification.
Send the drawing, bill of materials (BOM), purchase requirements, and required documentation with your first request. Those inputs set the sourcing scope and flag engineering or contracting questions early.
We evaluate C-parts on total cost of ownership (TCO): assembly requirements, replenishment, handling, and specification control, not unit price alone. Bufab’s network of 1,600+ suppliers across 30+ countries backs our sourcing, while CSG manages North American customer relationships locally.
Which military and aerospace standards govern mil-spec fasteners (AN, MS, NAS, NASM)?
The term mil-spec fasteners is a purchasing label, not a technical specification. A defensible order names the exact part number, governing document, revision, and drawing requirements. The label alone sets no material, strength, tolerance, or acceptance criteria.
Military drawings also cite aerospace and industry standards. AN, MS, NAS, and NASM designations appear across established equipment programs, and many legacy MS fastener standards now carry NASM designations. The prefix identifies the document family. It does not make two parts interchangeable.
Read the complete requirement, including the revision
A part standard defines one configuration or family. Separate specifications cover material, protective finish, testing, and packaging. Read every referenced document together, because the dimensional drawing is never the whole requirement.
Take MIL-DTL-18240. It covers self-locking elements on externally threaded bolts and screws used at 250°F maximum. When it appears on a drawing, the order carries requirements well beyond thread diameter and length. Confirm exactly which provisions the drawing and purchase order invoke.
Use the revision the contract or approved technical baseline specifies. A newer revision does not automatically replace the one called out for an existing program. Route canceled or superseded documents through your engineering approval process.
CSG’s guide to AN, MS, and NAS fastener standards breaks down each designation family. Use it to read the drawing, then verify the actual requirements for the part you are buying.
Build a purchase description that survives review
Your purchase description must identify the part and its acceptance requirements in full. Include these items wherever the drawing or contract calls for them:
- Complete part number, including dash numbers and configuration suffixes.
- Drawing and specification revisions that apply to the order.
- Material, strength requirements, finish, and any specified locking feature.
- Manufacturer identification and any limits on substitution.
- Required lot identification, inspection records, packaging, and marking.
What fasteners are used on armored and military vehicles?
Armored and military vehicles use bolts, screws, nuts, washers, pins, rivets, threaded inserts, and application-specific fastening systems. The approved drawing sets the hardware for each joint. No single military vehicle bolt fits every attachment.
Structural joints, equipment mounts, access panels, and electrical enclosures each carry different requirements. A fastener approved for an interior bracket is not automatically approved for a suspension attachment or an armor-related assembly.
Match the fastener to the joint
Start with the joint’s function and approved load requirements. Then review the clamped materials, tool access, thread engagement, service environment, and maintenance procedure. Keep the fastener, mating hardware, and installation instructions together through selection.
On removable access panels, check the specified screws, captive hardware, or latches. On thin-sheet attachments, check the approved threaded insert or rivet nut configuration. On locating or retaining components, check the specified pin type and retention method.
Locking nuts and other retention features need the same discipline. A locking feature does not replace the correct installation procedure. Follow the approved requirements for tightening, inspection, reuse, and replacement.
Treat substitutions as engineering changes
Never substitute a commercial fastener just because its nominal diameter, length, and apparent strength match. Thread form, grip length, coating, locking behavior, and inspection requirements matter just as much.
Submit every proposed alternative through the designated approval process before you buy it for production. Record the approved disposition against the affected part and order. That keeps a sourcing decision from turning into an undocumented configuration change.
What is the DLA Qualified Suppliers List for Manufacturers (QSLM)?
The Qualified Suppliers List for Manufacturers, or QSLM, is DLA’s list of pre-qualified manufacturers for selected items it buys and manages. The Qualified Suppliers List for Distributors, or QSLD, lists distributors that met DLA’s traceability and quality system requirements. The difference is the supplier’s role in the supply chain.
For fasteners, check the program status first. A 2023 DLA Aviation notice records the QSL program’s discontinuation effective February 20, 2023, for Class 2 and Class 3 threaded fasteners (FSC 5305, 5306, 5307, and 5310), quick release pins (FSC 5315), and rivets (FSC 5320). Contracts already awarded under the program stayed valid. Read the qualification clause in every solicitation, because requirements vary by commodity.
The closure does not remove every qualification requirement. Some military specifications carry their own Qualified Products List (QPL), a separate product-level qualification. When a solicitation cites a QPL, the delivered part still has to be a listed product from a listed source, whatever its QSL status.
A distributor listing is not a manufacturer qualification. A manufacturer listing says nothing about the distributors selling its parts. CSG is a distributor, so ask us which DLA status applies to your solicitation instead of assuming a manufacturer listing.
Check the listing against the actual purchase
Qualification is never blanket approval for everything a company sells. Match the listed organization and its scope to the hardware you are buying. Confirm any facility, commodity, or other limits in the program documentation.
Check status when you buy, not from an old supplier presentation or a saved screenshot. The order must satisfy the solicitation in front of you. Another quality program does not replace a listing the solicitation specifically requires.
Keep supplier qualification separate from product evidence
Supplier qualification and product conformity answer different questions. Qualification covers the supplier under a defined program. Product evidence shows whether the delivered hardware meets the order.
Review both before acceptance. A qualified source still has to deliver the correct part with the Certificates of Conformance (CoC), mill test reports (MTRs), and full lot traceability the order calls for. A clean dimensional inspection does not replace a supplier qualification the contract requires.
Preserve identity through receiving and kitting
Receiving procedures must keep the link between the purchase order, package identification, and required lot records. Define how that identity carries over when hardware moves into smaller containers or assembly kits.
In mixed kits, keep the required identification for each component, because the kit label alone is not sufficient evidence. Set the record structure before repackaging starts. You then isolate a discrepancy without putting unrelated material on hold.
What is the difference between the Berry Amendment and DFARS 252.225-7009 specialty metals rules?
The Berry Amendment (10 U.S.C. 4862) restricts Department of Defense purchases of listed categories such as food, clothing, textiles, and hand or measuring tools. Specialty metals sit in a separate statute (10 U.S.C. 4863) and reach your order through DFARS 252.225-7009. For fasteners made of specialty metals, that clause decides which sources you can use.
What DFARS 252.225-7009 specialty metals compliance requires
The clause defines specialty metals as steel above set alloy limits, nickel and iron-nickel alloys, cobalt alloys, titanium and titanium alloys, and zirconium and zirconium alloys. Specialty metal in delivered items must be melted or produced in the United States, its outlying areas, or a qualifying country under DFARS 225.003. Stainless steel, many alloy steels, titanium, and nickel-alloy fasteners all fall inside that definition.
Where the COTS fastener exception holds and where it fails
The clause exempts most commercially available off-the-shelf (COTS) items, but it carves out COTS fasteners. A COTS fastener stays exempt only when it goes into a COTS end item, subsystem, assembly, or component, or when its manufacturer qualifies under paragraph (c)(3). That paragraph requires the manufacturer to certify it will buy domestically melted or produced specialty metal equal to at least 50 percent of the specialty metal it purchases for fastener production during the calendar year.
A fastener made to a government drawing counts as COTS only if it is also sold in substantial quantities in the commercial marketplace and offered without modification. Do not assume the exception covers it. A separate minimal content exception in paragraph (c)(6) allows noncompliant specialty metal up to 2 percent of the total weight of all specialty metals in the end item. Confirm which exception, if any, applies with your contracting officer before you select the source.
What environmental seals and O-rings are used in military equipment?
Military equipment uses O-rings, gaskets, and other seals specified for the assembly’s fluids, temperatures, pressures, and exposure. The approved seal specification sets the material and performance requirements. A military application or a matching outside diameter proves nothing about suitability.
Seals and O-rings sit in the same joints as fasteners, and many defense assembly kits and replenishment programs carry both. They need the same specification control as the bolts beside them.
Seals sit in hydraulic connections, fuel systems, electrical enclosures, access covers, and other assemblies. Treat each location as its own application. A compound approved for one fluid system is not approved for another by default.
Separate dimensional standards from material requirements
SAE AS568 defines standard O-ring sizes. A size designation does not identify the material or performance requirements. Your purchase description also needs the compound specification and any drawing-specific conditions.
Military seal requirements include MIL-DTL-25988, which covers fluorosilicone rubber for O-rings, compression seals, and molded parts. Confirm the required type, class, grade, and configuration against the drawing.
Never identify an elastomer compound by color alone. Use the specified material identification and supporting documentation. Review storage, packaging, and shelf-life requirements wherever the applicable documents set them.
Review the complete sealing interface
Seal selection includes the mating hardware and assembly conditions. Review gland dimensions, surface requirements, installation damage risks, and any specified lubricant. Follow the approved procedure, and never swap in a look-alike seal during assembly.
On an enclosure, evaluate the gasket, fastener pattern, and compression requirements together. Uneven tightening or a wrong replacement part changes the assembled interface. Environmental acceptance belongs to the specified assembly and test conditions, not a general material description.
These selection principles do not define CSG’s supply scope for any specific seal. We confirm product availability and required documentation during the sourcing review.
Where defense hardware orders lose control
- Incomplete purchase descriptions: The order states the base part number but drops a required suffix, finish, or revision. The delivered hardware then needs extra review before acceptance. Resolve missing information during quotation, and carry the approved description into the purchase order in full.
- Legacy callouts read against the wrong document: An older MS or AN callout now points to a NASM or other replacement document, while the prime contract locks in the original baseline revision. Quoting against the newer document without approval creates a configuration mismatch. Confirm with engineering which document governs the order before the RFQ goes out.
- Qualification confused with conformity: A supplier listing gets treated as proof that every delivered item meets the drawing. Keep supplier approval, part identification, and acceptance evidence as separate review points. Each one answers a different question and needs its own record.
- Counterfeit exposure from undocumented sources: Hardware bought through brokers with no chain back to the manufacturer arrives with no way to prove it is authentic. SAE AS6174 sets practices for buying authentic and conforming materiel through certification, traceability, testing, and inspection matched to the item. Buy from sources that document the chain to the original manufacturer.
- Finish changes released as purchasing decisions: Lead times and restrictions on cadmium and hexavalent chromium push buyers toward zinc-nickel or trivalent alternatives. A drawing that calls out cadmium plating under QQ-P-416 or SAE AMS-QQ-P-416 needs an approved engineering change before a different finish ships. Treat the finish as part of the part number, not a sourcing preference.
- Broken identity after repackaging: Hardware moves from labeled packaging into bins or kits without its lot connection. Define the transfer process before material reaches production. Specify which identifiers stay visible and where the supporting records live.
- Unapproved substitutions under schedule pressure: A replacement looks dimensionally equivalent, so purchasing releases it before engineering review. Document the proposed difference and get the required disposition first. Include mating hardware, finish, locking features, and installation instructions in that review.
- Specialty metals clauses checked too late: The team assumes the COTS fastener exception applies, then contract review finds DFARS 252.225-7009 requires domestic or qualifying-country melt. Review the applicable clauses with the procurement package. Assign open questions to the right engineering, quality, or contracting authority before order release.
What to Settle Before You Send a Mil-Spec Fastener RFQ
Settle the approved technical baseline first: part number, governing document, revision, and drawing notes. Then confirm the source, the Certificates of Conformance (CoC), mill test reports (MTRs), and full lot traceability the contract calls for, plus installation conditions and replenishment. Working in that order turns recurring specification disputes into defined purchasing and acceptance decisions.
Before you release the RFQ, decide who holds substitution authority, which DFARS 252.225-7009 exception applies if any, and whether the solicitation cites a QSL or QPL requirement. List those sourcing requirements separately from the part description. Suppliers then quote against a clear, complete basis.
Send your RFQ to our OEM team with your drawings, bill of materials, and purchasing requirements. We review the sourcing scope and work through the engineering, kitting, and replenishment needs for your program.
Frequently Asked Questions (FAQs)
How do you cross-reference an NSN to a mil-spec fastener part number?
A National Stock Number (NSN) has 13 digits. The first four are the Federal Supply Class, such as FSC 5305 for screws, and the last nine are the National Item Identification Number (NIIN). DLA’s Federal Logistics Information System (FLIS) links each NSN to reference part numbers and the CAGE codes of their sources. Match the cross-referenced MS, NAS, or AN part number to your drawing and revision before you buy, because an NSN reference alone does not approve a source for your program.
How do buyers verify mil-spec fastener suppliers after DLA Aviation discontinued the QSLM and QSLD program?
Buyers verify sources against the solicitation itself: QSL clauses on existing awards, any QPL the cited specification requires, quality certifications, and documented traceability to the manufacturer. CSG holds ISO 9001:2015 and AS9120 Rev B certification, ITAR registration, and JCP Certification. We also provide kitting and vendor-managed inventory for defense programs.
What is the difference between DLA QSLM and QSLD?
QSLM is the DLA list of pre-qualified manufacturers, and QSLD is the DLA list of distributors that met its traceability and quality system requirements. For Class 2 and Class 3 threaded fasteners, quick release pins, and rivets, DLA Aviation discontinued the program effective February 20, 2023. Neither listing proves that delivered hardware meets your purchase order.
Are commercial fasteners interchangeable with military-standard fasteners?
No. Matching nominal diameter and length does not make two fasteners interchangeable. Material, finish, thread form, locking features, and acceptance requirements all need review, and the substitute needs approval through your engineering change process first.
Does the Berry Amendment or DFARS 252.225-7009 apply to mil-spec fasteners?
For fasteners made of specialty metals, DFARS 252.225-7009 is the clause that applies. It requires specialty metals such as stainless steel, titanium, and nickel alloys to be melted or produced in the United States, its outlying areas, or a qualifying country. The Berry Amendment covers other categories, such as textiles and hand or measuring tools. COTS fasteners are exempt only under the clause’s stated conditions, so check the contract before you select the source.
What traceability documents are required for mil-spec fasteners on defense contracts?
The contract and drawing set the list. Common requirements include the manufacturer’s Certificate of Conformance (CoC), mill test reports (MTRs) or material certifications, plating and heat-treat certifications, lot or heat identification, and the manufacturer’s CAGE code. Name each required document in the RFQ so the quote covers it.

