We're currently making updates to enhance your experience. If you encounter any technical difficulties or can't find what you need, please contact us and we'll be happy to help. Thank you for your patience as we make these improvements to our site.
(937) 433-7200
contactus@componentsolutionsgroup.com
bufab-logo-white
EcoVadis Platinum medal, Top 1%, Sustainability Rating, October 2025
TIME World's Best Companies 2025, Sustainable Growth badge
We're currently making updates to enhance your experience. If you encounter any technical difficulties or can't find what you need, please contact us and we'll be happy to help. Thank you for your patience as we make these improvements to our site.

Do Split Lock Washers Work? What Vibration Testing Shows

Share:

Quick answer

Split lock washers do not work under transverse vibration testing. NASA’s Fastener Design Manual reports they flatten at installation torque, lose spring tension, and then act as a plain flat washer, loosening on the same curve. They hold only slight tension against mild thermal movement. Wedge lock washer pairs and anaerobic thread lockers rate excellent instead.

Split lock washers do not lock. NASA put that in writing. The agency’s Fastener Design Manual (NASA RP-1228) reports that a helical spring washer flattens the moment you torque the bolt, then acts as a plain flat washer, and concludes that “a lockwasher of this type is useless for locking.”

Do split lock washers work? Under transverse vibration testing, no. They flatten at installation torque, lose their spring tension, and loosen on the same curve as a plain washer. They hold slight tension against mild thermal movement, and that is the limit of what they deliver.

That finding matters because transverse vibration beats thread friction. Side-to-side joint movement breaks the frictional grip under the bolt head and at the bearing face. Once friction drops away, the thread behaves like an inclined plane and the fastener backs out. Engineers call the result fastener self-loosening.

Fastening Method Transverse Vibration Resistance Reusability Temperature Limit
Wedge Lock Washer Pairs Excellent High (inspect before reuse) Up to roughly 300 °C (alloy dependent)
Prevailing Torque Nut Good Limited (1 to 3 cycles) About 120 °C nylon insert; far higher all-metal
Anaerobic Thread Locker Excellent Reapply every time 150 °C standard; 230 °C high-temp grades
Tooth Lock Washer Fair None (single use) Material dependent
Split Lock Washer Poor None (single use) Material dependent

 

The Core Engineering Problems in Joints That Move

Loss of Preload

Clamp load is what stops two parts from moving against each other. Torque stretches the bolt, and that stretch pulls the joint tight.

Embedment, vibration, and yielding all relax the stretch. Thread friction falls with it, and at zero friction an outside force turns the nut with almost no resistance.

Transverse Slippage

Axial vibration pulls along the bolt axis. It trims clamp load briefly but rarely spins a fastener loose on its own.

Transverse vibration slides the mating faces perpendicular to the bolt. That motion strips friction from every contact surface at the same time, and it is the main reason standard fasteners back out.

Thermal Cycling

Dissimilar materials expand and contract at different rates. Heat thickens the joint and raises bolt tension, then cooling hands that tension back.

Repeated cycles crush the microscopic high spots on the mating faces. The joint gets thinner, preload falls, and vibration finishes the job.

Micro-Slippage and Fatigue Cracking

Long before a joint visibly loosens, the faces micro-slip. Each small movement frets the contact surfaces and cycles bending stress into the first engaged thread, which is where fatigue cracks start.

A fastener that fatigues does not rattle out of the hole. It shears, and the joint fails with no loose hardware to warn the maintenance crew first.

Retorque Labor, Thread Galling, and Warranty Claims

Joints that rely on friction alone buy their security with labor. Crews schedule retorque rounds, pull access panels, and recheck hardware that should hold on its own.

Vibration-polished and corroded threads gall on removal, so a routine check turns into a drill-out and a tapped repair. When a loose fastener reaches the customer, it returns as a warranty claim against the OEM, not against the washer. Bolted joint integrity is a product-cost line, not a shop-floor detail.

What the DIN 65151 Junker Test Reveals About Fastener Security

Engineers measure joint security with the DIN 65151 Junker test. Gerhard Junker developed the method in the 1960s, and it is still the benchmark for transverse vibration.

The rig clamps a bolted joint and drives the lower plate sideways at a fixed amplitude and frequency. A load cell records the clamp load left in the bolt through every cycle.

Plain nuts shed clamp load in the opening cycles and run to zero in short order. Split lock washers track almost the same curve. Flattened at installation torque, the split ring adds no rotational resistance once the joint starts to slip.

DIN 65151 Junker test results separate marketing claims from mechanics. Critical joints need verified vibration-resistant fasteners that block counter-rotation or hold tension mechanically.

1. Wedge Lock Washer Pairs

Wedge lock washers hold joints with tension instead of friction. They install as a bonded pair, cams facing each other on the inside and radial teeth gripping the outside.

The cam angle is steeper than the thread pitch of the bolt. To rotate loose, the bolt has to stretch further, and the rising tension stops the rotation.

  • Best for: Heavy equipment, aerospace components, and severe vibration service.
  • Cost profile: Higher unit cost that pays back through fewer warranty claims and less field maintenance.
  • Standout features: Mechanical locking that works independently of lubrication and surface friction.

Advantages

  • Holds high clamp load through aggressive Junker testing.
  • Performs across wide temperature ranges in the right alloy.
  • Reusable after inspection and re-lubrication.

Disadvantages

  • Operators have to install the bonded pairs in the correct orientation.
  • Costs more than a stamped flat washer.

2. Prevailing Torque Nuts

A prevailing torque nut resists rotation through physical interference. It takes wrenching force to turn before it ever touches the joint face.

Nylon insert nuts use a polymer ring that deforms around the bolt threads. All-metal versions use distorted top threads to hold friction against the bolt, so the nut stays put even after clamp load disappears.

  • Best for: Automotive assemblies, rail infrastructure, and joints where losing a fastener is unacceptable.
  • Cost profile: Moderate unit cost that works at high volume.
  • Standout features: Stays on the bolt shaft even when initial tension drops to zero.

Advantages

  • Stops total fastener loss.
  • All-metal designs run far past the roughly 120 °C (250 °F) ceiling of a nylon insert.
  • Simple to inspect visually on the line.

Disadvantages

  • Nylon inserts break down in hot service, including engine compartments.
  • Thread deformation limits reuse, so most get replaced after one or two cycles.

3. Anaerobic Thread Lockers

Liquid thread lockers are adhesives applied to the threads before assembly. They cure without air and in contact with active metal, filling the gaps between male and female threads with hard thermoset plastic.

That bond ties the assembly together and shuts down lateral movement in the thread.

  • Best for: Precision electronics, engine components, and joints where a washer would mar the mating surface.
  • Cost profile: Pennies per application.
  • Standout features: Seals the thread against moisture and blocks corrosion inside the joint.

Advantages

  • Delivers high breakaway torque.
  • Spreads load across the full engaged thread length.
  • Keeps fluids out of the joint.

Disadvantages

  • Threads have to be clean and oil free before application.
  • High-strength grades need applied heat and dedicated tools to remove in the field.

4. Why Conventional Split Lock Washers Fail the DIN 65151 Test

Split washers are helical springs cut to leave two offset edges. External and internal tooth washers use twisted prongs that bite into the bolt head and the mating material. Neither design survives the Junker rig, because both depend on friction that transverse slip removes in the opening cycles.

Plenty of legacy drawings still call them out. Testing puts them in static duty only. Our washer product overview covers where they still earn a place.

  • Best for: Light-duty consumer goods, static structures, and electrical grounding connections.
  • Cost profile: Commodity pricing, the lowest in this group.
  • Standout features: Tooth styles cut through paint and hold a conductive path.

Advantages

  • Holds slight tension against minor thermal movement.
  • Very cheap for high-volume, low-risk builds.

Disadvantages

  • Loses preload under continuous transverse vibration.
  • Tooth styles gouge the mating surface and open the door to local corrosion.

How Secondary Fastening Methods Behave Under Stress

Procurement teams often ask how self tapping screws work under repeated transverse load. They cut or roll their own mating thread, so the fit runs near zero clearance and resists loosening better than a machine screw in an oversized tapped hole. Push the vibration high enough and that thread still walks backward without a secondary locking feature.

Thin sheet metal and tubular frames raise a second question: how rivet nuts work. A rivet nut delivers full thread engagement in material too thin to tap, and it handles shear and pull-out loads well. The bolt running into it still needs thread locker or a prevailing torque feature to survive vibration.

Pins solve a different problem. Dowel pins and spring pins hold no tension; they absorb the transverse sliding force between two plates. Move that shear load onto a pin and the bolt only has to hold vertical tension, which takes away the motion that drives self-loosening.

How Component Solutions Group Supports Vibration-Critical Joints

Component Solutions Group is an engineered supply chain partner and specialty distributor for OEM manufacturers across North America. Backed by the Bufab Group, CSG handles global sourcing, vendor-managed inventory (VMI), kitting, and quality control for engineered fasteners and C-class components. CSG works under ISO 9001:2015 and AS9120B quality systems, is ITAR registered, and its A1 Fastener division is IATF 16949 certified; the full list is on the CSG quality page.

Procurement managers use CSG to simplify complex bills of materials, hold delivery schedules, and standardize vibration loosening prevention across programs instead of leaving the decision to each individual print.

The result is fewer line-down events and fewer warranty surprises.

What to Ask Before You Specify a Locking Method

  • Is the dominant force axial or transverse? Transverse movement calls for wedge washers or structural adhesive. Axial loads call for correct bolt elongation and enough clamp force.
  • What is the maximum operating temperature? Nylon inserts fail in engine compartments and standard thread lockers lose strength above 150 °C, which pushes you to all-metal prevailing torque nuts or high-temperature alloys.
  • Will the joint see field service? High-strength chemical lockers make disassembly hard, so mechanical options like wedge lock washers and nuts win on serviceable assemblies.
  • Who pays for the retorque schedule? If the answer is the service organization or the warranty budget, the higher-cost locking feature is the cheaper part.
  • Do you have enough thread engagement? No locking feature saves a stripped bolt. Run the numbers with our online calculators and converters and confirm the fastener has the thread depth to take full torque.

Predictable assembly performance starts with the right component on the print. Contact our OEM team to submit an RFQ, request a sample kit, or review your current bill of materials.

Where a joint must hold preload through relaxation, a conical spring washer is another option; see our Belleville washer guide.

Frequently Asked Questions (FAQs)

Why did NASA say split lock washers are useless?

NASA’s Fastener Design Manual (RP-1228) found that a helical spring washer flattens under installation torque and then behaves as a plain flat washer. With the spring collapsed, the two split ends apply no meaningful resistance to rotation. On that basis the manual states that a lockwasher of this type is useless for locking.

Can you reuse a split lock washer?

No. Installation torque flattens the washer and the metal yields, so the spring tension is gone for good. A reused split washer brings nothing to the joint.

What is the best alternative to a split ring washer?

Wedge lock pairs give the strongest mechanical resistance to transverse vibration. Where a washer does not suit the application, liquid thread locking methods and prevailing torque nuts both hold well.

What is the best anti-vibration washer for heavy machinery?

Wedge lock washer pairs. The cam angle exceeds the thread pitch, so the bolt has to stretch before the joint can rotate loose, which holds under the transverse shock loading heavy equipment sees. Specify them with verified thread engagement and a documented retorque check after the first duty cycle.

Are prevailing torque nuts better than lock washers?

Yes. They grip the thread through physical interference, so the nut stays on the bolt even after clamp load drops to zero. A split washer offers no such backstop.

Where do split lock washers still make sense?

Split lock washers belong in static duty only: light-duty consumer goods, static structures, and electrical grounding connections, where tooth styles cut through paint and hold a conductive path. They hold slight tension against minor thermal movement and cost very little for high-volume, low-risk builds, but they lose preload under continuous transverse vibration.

Stay Informed

Get exclusive ebooks, resources, and industry insights from us every month.

  Thank you for Signing Up

Related Posts