We're currently making updates to enhance your experience. If you encounter any technical difficulties or can't find what you need, please contact us and we'll be happy to help. Thank you for your patience as we make these improvements to our site.
(937) 433-7200
contactus@componentsolutionsgroup.com
bufab-logo-white
EcoVadis Platinum medal, Top 1%, Sustainability Rating, October 2025
TIME World's Best Companies 2025, Sustainable Growth badge
We're currently making updates to enhance your experience. If you encounter any technical difficulties or can't find what you need, please contact us and we'll be happy to help. Thank you for your patience as we make these improvements to our site.

Clearance Hole Chart: Inch and Metric Close, Normal and Loose Fit

Share:

Quick answer

A clearance hole is an unthreaded hole drilled larger than the fastener so the bolt passes through freely. ISO 273 sets metric sizes and ASME B18.2.8 sets inch sizes, each in close, normal and loose fits. The charts below list both. Component Solutions Group (CSG) supplies spec-compliant fasteners for these joints.

An M8 bolt will not pass through an 8 mm hole; ISO 273 gives it 8.4, 9.0 or 10.0 mm depending on the fit. Undersized holes stall automated assembly lines. Oversized holes cost bearing area under the bolt head. Both send parts back for rework, and the right clearance class on the drawing prevents all three.

How CSG Supplies This

Component Solutions Group (CSG), a Bufab company headquartered in Dayton, Ohio, distributes engineered fasteners and C-class components to OEMs. We do not manufacture fasteners. We source, stock and deliver spec-compliant hardware with a 99.9% order accuracy rate.

Our services include vendor-managed inventory (VMI), kitting and global sourcing backed by the Bufab network of 1,600+ suppliers in 30+ countries. The brands we distribute include BUMAX, Böllhoff, HellermannTyton, ITW Nexus, Sherex and Southco.

CSG holds ISO 9001:2015 and AS9120 Rev B certification. CSG’s Automotive & Tier 1 division (A1) is IATF 16949 certified.

Metric Clearance Hole Chart (ISO 273)

ISO 273 defines three metric clearance series: fine, medium and coarse. IsoCNC maps them to ISO 286 hole tolerance classes H12, H13 and H14. Fine is the close fit, medium is normal and coarse is loose.

Never draw the hole at the bolt size. Sizemarker notes that an 8 mm hole for an M8 bolt specifies an interference fit, and the part will not go together. An M8 bolt takes an 8.4 mm, 9.0 mm or 10.0 mm hole, depending on the fit.

Metric Size Close Fit, Fine H12 (mm) Normal Fit, Medium H13 (mm) Loose Fit, Coarse H14 (mm)
M3 3.2 3.4 3.6
M4 4.3 4.5 4.8
M5 5.3 5.5 5.8
M6 6.4 6.6 7.0
M8 8.4 9.0 10.0
M10 10.5 11.0 12.0
M12 13.0 13.5 14.5

 

These values suit most OEM and automated assembly joints. High-vibration OEM joints also need a check of preload and locking hardware, because hole clearance alone does not keep a bolt tight. Confirm every hole size against the governing standard or your drawing before production.

Inch Clearance Hole Chart (ASME B18.2.8)

ASME B18.2.8 sets inch clearance holes in the same three classes: close, normal and loose. The table below lists hole diameters in inches for common sizes, plus the normal-fit drill. True Precision Machining publishes a fuller inch table.

Thread pitch does not change the hole. Hole size follows the nominal fastener diameter, so a 1/4-20 UNC bolt and a 1/4-28 UNF bolt use the same clearance hole. Check hex cap screw dimensions in our bolt size chart before you release the bill of materials.

Inch Size Close Fit (in) Normal Fit (in) Loose Fit (in) Normal-Fit Drill
#10 (0.190) 0.206 0.221 0.238 #2
1/4 0.266 0.281 0.297 9/32
5/16 0.328 0.344 0.359 11/32
3/8 0.391 0.406 0.422 13/32
1/2 0.531 0.562 0.609 9/16

What Breaks When Hole Clearances Are Wrong

Most clearance problems trace back to the drawing. Each one shows up on the assembly floor.

Undersized Holes Stop the Line

A hole drawn at or near bolt size will not accept the fastener. Operators force the bolt, damage threads or plating, or send the part back for CNC machining rework. When tight tolerance stacks cause the miss, every reworked part adds labor and delays the build.

Robotic Cells Jam on Tight True Position

Automated assembly cells drive each bolt to a programmed coordinate. A close-fit hole that sits slightly off true position puts the bolt tip on the edge of the hole instead of in it. The cell faults, and an operator has to clear it by hand. Normal-fit holes give the robot room to land the bolt.

Oversized Holes Weaken the Joint

A hole larger than the chart value shrinks the bearing surface under the bolt head and nut. It also lets parts shift before the joint is tightened. Quality teams then flag misaligned assemblies for rework.

Washers Cup Into Oversized Holes

A loose-fit or oversized hole leaves a thin ring of material to carry the clamp load. A thin or soft washer over that hole cups into it or embeds in the surface, and the joint loses preload as it settles. A hardened washer wide enough to cover the hole spreads the load back onto solid material.

Tolerance Stacks Fail in Multi-Plate Assemblies

Every plate in a bolted stack carries its own hole position error. With close-fit holes, those errors combine and the bolt binds, even when each part passes inspection on its own. The position tolerance section below shows how to size the clearance for the whole stack.

Rework Drives Up Cost

Scrapped parts and re-drilled holes trigger replacement hardware and rush orders. Procurement teams absorb that cost through emergency purchase orders and expedited freight. The correct clearance class on the drawing prevents it.

When to Use Close, Normal and Loose Fits

Pick the fit by what the joint must do: locate parts, assemble easily or absorb misalignment.

Close fit. Use it when the bolt must locate the parts precisely. Close fit leaves little room for error, so it demands accurate hole locations and good true position.

Normal fit. This is the default for most assemblies. When a drawing says only “clearance hole,” it almost always means normal fit. It gives easy assembly for bolts and screws without giving up much bearing area under the head.

Loose fit. Use it for multi-fastener bolt patterns where tolerance stacks across many holes. It also suits parts that change size with temperature and structures assembled in the field or as fabricated.

Clearance Hole vs. Tap Drill Hole vs. Pilot Hole

These three holes do different jobs. Mixing them up on a drawing produces parts that will not assemble.

Clearance hole. The full fastener passes through without touching the walls. A nut or a tapped part on the far side carries the clamp load.

Tap drill hole. This hole is sized for threading. It is smaller than the fastener’s major diameter, and a tap then cuts internal threads into it. Size it with our tap drill size calculator or the tap drill size chart.

Pilot hole. A small starter hole guides a larger drill or a self-tapping screw. It keeps the drill from walking and cuts the force needed for the final operation. Our drill bit size chart covers fractional, number, letter and metric bits.

Hole Position Tolerance When Several Holes Must Line Up

A single-bolt joint rarely has alignment trouble. A multi-bolt pattern, such as a flange or mounting plate, is different. Every hole must line up with its mate at the same time.

Geometric dimensioning and tolerancing (GD&T) controls how far each hole sits from true position. The clearance gap sets how much positional error the joint absorbs. A close fit on a six-bolt flange leaves almost no margin, so one stray hole blocks assembly.

The floating fastener formula in ASME Y14.5 links the two: T = H − F, where H is the smallest allowed hole and F is the largest fastener. An M8 bolt in a 9.0 mm normal-fit hole leaves about 1.0 mm of position tolerance for each part, against about 0.4 mm in an 8.4 mm close-fit hole. A GD&T tolerance stack-up analysis carries that check across every plate, datum and fixture, so the flange bolt clearance gap covers every source of error in the assembly.

Normal and loose fits give the machinist more positional tolerance. Bolts shift slightly inside their holes and still assemble without binding. Wider tolerance is easier to hold, which keeps machining and final assembly on schedule.

Additive manufacturing adds another source of error. FDM-printed holes commonly come out undersize, so many shops print the hole small, then drill or ream it to the chart value.

Lock the Fit Class Before the Drawing Is Released

Write the standard and the fit class into every hole callout, for example “9.0 mm clearance, ISO 273 medium.” Purchasing, the machine shop and the assembly cell then work from the same number. Nobody has to guess what a bare “clearance hole” means.

Then match the hardware to the hole. Loose-fit holes need hardened washers that cover the hole. Robotic cells need fasteners whose head and thread dimensions stay consistent from lot to lot.

Need spec-compliant fasteners for your next build? Contact our OEM team for a quote on the bolts, nuts and washers your drawings call for.

Frequently Asked Questions (FAQs)

Does thread pitch affect clearance hole size?

No. Hole size follows the nominal fastener diameter, not the thread pitch. A 1/4-20 UNC bolt and a 1/4-28 UNF bolt use the same clearance hole.

What happens if you draw a hole at the exact bolt diameter?

You specify an interference fit, and the part will not go together. An M8 bolt needs a hole of at least 8.4 mm, not 8 mm.

What size drill bit is used for an M8 clearance hole?

A 9 mm drill gives the ISO 273 medium (normal) fit, which is the default for most joints. Use an 8.4 mm drill for a close fit and a 10 mm drill for a loose fit.

What does “clearance hole” mean on a drawing with no fit class?

It almost always means normal fit, the default for most assemblies. Call out close or loose fit on the drawing when the joint needs it.

Do loose fit clearance holes require special washers?

They do not need special washers, but they do need one that fully covers the hole. A hardened flat washer spreads clamp load past the reduced bearing area and resists cupping.

What tolerance class is the ISO 273 medium fit?

The medium (normal) fit uses ISO 286 hole tolerance class H13. The fine (close) fit uses H12, and the coarse (loose) fit uses H14.

Stay Informed

Get exclusive ebooks, resources, and industry insights from us every month.

  Thank you for Signing Up

Related Posts